Upgrade your YFZ450R's footpeg game with our Pro Pegs — Built from heavy-duty steel with a durable powder coat finish, these pro pegs deliver the aggressive grip and factory-style look your machine deserves. Whether you're ripping through trails or hitting the track, Pro Pegs keep your feet planted and in control
What's Included:
(2) Pro Peg Mounts
(1) Front Mount
(2) Pro Peg Nerf Bars
(1) Hardware pack includes:
(2) 8mm x 50mm bolts,
(4) 8mm x 20mm bolts,
(16) 8mm flat washers,
(6) 8mm nylock nuts,
(6) 6mm x 80mm bolts,
(14) 6mm flat washers,
(8) 6mm nylock nuts,
(2) aluminum rear nerf bar brackets,
(2) front net mounts, (2) rear net mounts
(4) Black Nets
(2) front nets (2) rear nets
Bolt-on fit With Drilling 21/64 Holes
(2) Heavy-Duty Steel Construction Foot Peg Mounts powder coated black S/S Foot Peg Cleats for grip Aluminum Nerf Bars 1 5/16 .x 130 wall aluminum tubing
Nets 1" heavy duty webbing
Compatible: Yamaha YFZ450R 2009-2026
Installation Steps:
1. Park and secure your ATV. Place the TRX450R on a flat surface and engage the parking brake. Allow the engine to cool completely before beginning.
2. Remove the stock footpegs. Remove the bolts securing the OEM footpegs on both sides. Set the stock pegs aside. Wipe down the peg mounting brackets with a clean rag to remove any dirt, grease, or debris for a secure fit. Install the new peg mounts using stock bolts. There is a left and right side. The right side has (2) welded on spacers. Leave bolts loose for now. Remove motor mount bolts (front) both sides. Slide front mount into place and reinstall stock bolts. Leave them loose for now
3. Position the Nerf Bars
Slide the nerf bars onto front mount and into end of pegs. Now stand ATV up on rear grab bar. Make sure nerf bars are slid all the way together on the front mount. Now measure and mark 1" from end of nerf bar. Using 21/64 drill bit drill a hole through nerf bar and mount. Put a 8mm x 50mm bolt through the hole drilled using a 8mm flat washer on bolt sides and put a 8mm nylock nut finger tight. Repeat this step for the opposite side.
Set front of Quad back on the ground. Install the the (2) rear nerf bars brackets to the rear fender supports using 8mm x 20mm bolts and washers. Tighten all mounting bolts and torque front motor mount and peg mounting bolts to manufacturer specs.
4. Install Nets, Brackets, and S/S Pegs
Slide the S/S pegs over the pins and align holes with pins. Using the 6mm x 80mm bolts slide them through a 6mm washer and then trough front net mount. There is a left and right mount. The right side net tab goes to the inside of the slot and the left side will be opposite. Install the rear net mount by sliding over the 6 x 80 bolts and use a 6mm washer before putting on the 6mm nylock nuts. Tighten all 6 bolts securely.
Install the nets. The front nets are longer than the rear. Slide them through the slots and back through the middle slot. Leave them loose until all straps are in place. Adjust nets to desired position.
5. Inspect and test.
Give each peg a firm shake to confirm there is no movement or play. Visually inspect the hardware on both sides before riding.
You're Ready to Ride. Your Pro Pegs are now installed and ready for the trail. Note: Always refer to your Yamaha YFZ450R 2009-2026 service manual for model-specific torque specifications. If you have any questions about fitment or installation, contact us before riding.
){kind=link}